Analog cellular systems use very narrow radio channel (small amount of bandwidth) that varies from 10 kHz to 30 kHz. Analog systems usually send control information in digital (data) form. The data signaling rates determine how fast messages can be sent on control channels. The RF power level of mobile telephones and how the power level is controlled ordinarily determines how far away the mobile telephone can operate from the base station (radio tower).

Regardless of the size and type of radio channels, all cellular and PCS systems allow for full duplex operation. Full duplex operation is the ability to have simultaneous communications between the caller and the called person. This means a mobile telephone must be capable of simultaneously transmitting and receiving to the radio tower. The radio channel from the mobile telephone to the radio tower is called the uplink and the radio transmission channel from the base station to the mobile telephone is called the downlink. The uplink and downlink radio channels are normally separated by 45 MHz to 80 MHz.

In early mobile radio systems, a mobile telephone scanned the limited number of available channels until it found an unused one, which allowed it to initiate a call. Because the analog cellular systems in use today have hundreds of radio channels, a mobile telephone cannot scan them all in a reasonable amount of time. To quickly direct a mobile telephone to an available channel, some of the available radio channels are dedicated as control channels. Most cellular systems use two types of radio channels, control channels and voice channels. Control channels carry only digital messages and signals, which allow the mobile telephone to retrieve system control information and compete for access.

A mobile telephone's attempt to obtain service from a cellular system is referred to as access. Mobile telephones compete on the control channel to obtain access from a cellular system. Access is attempted when a command is received by the mobile telephone indicating the system needs to service that mobile telephone (such as a paging message indicating a call to be received) or as a result of a request from the user to place a call. The mobile telephone gains access by monitoring the busy/idle status of the control channel both before and during transmission of the access attempt message. If the channel is available, the mobile station begins to transmit and the base station simultaneously monitors the channel's busy status. Transmissions must begin within a prescribed time limit after the mobile station finds that the control channel access is free, or the access attempt is stopped on the assumption that another mobile telephone has possibly gained the attention of the base station control channel receiver. 

If the access attempt succeeds, the system sends out a channel assignment message commanding the mobile telephone to tune to a cellular voice channel. When a subscriber dials the mobile telephone to initiate a call, it is called "origination". A call origination access attempt message is sent to the cellular system that contains the dialed digits, identity information along with other information. If the system allows service, the system will assign a voice channel by sending a voice channel designator message, if a voice channel is available. If the access attempt fails, the mobile telephone waits a random amount of time before trying again. The mobile station uses a random number generating (an internal algorithm) to determine the random time to wait. The design of the system minimizes the chance of repeated collisions between different mobile stations, which are both trying to access the control channel since each one waits a different random time interval before trying again if they have already collided on their first, simultaneous attempt.

To receive calls, a mobile telephone is notified of an incoming call by a process called paging. A page is a control channel message that contains the telephone's Mobile Identification Number (MIN) or telephone number of the desired mobile phone. When the telephone determines it has been paged, it responds automatically with a system access message that indicates its access attempt is the result of a page message and the mobile telephone begins to ring to alert the customer of an incoming telephone call. When the customer answers the call (user presses "SEND" or "TALK"), the mobile telephone transmits a service request to the system to answer the call. It does this by sending the telephone number and an electronic serial number to provide the users identity. 

After a mobile telephone has been commanded to tune to a radio voice channel, it sends mostly voice or other customer information. Periodically, control messages may be sent between the base station and the mobile telephone. Control messages may command the mobile 

To conserve battery life, a mobile phone may be permitted by the base station to only transmit when it senses the mobile telephone's user is talking. When there is silence, the mobile telephone may stop transmitting for brief periods of time (several seconds). When the mobile telephone user begins to talk again, the transmitter is turned on again. This is called discontinuous transmission.

Figure 1.14 shows a basic analog cellular system. This diagram shows that there are two types of radio channels; control channels and voice channels. Control channels typically use frequency shift keying (FSK) to send control messages (data) between the mobile phone and the base station. Voice channels typically use FM modulation with brief bursts of digital information to allow control messages (such as handoff) during conversation. Base stations typically have two antennas for receiving and one for transmitting. Dual receiver antennas increases the ability to receive the radio signal from mobile telephones which typically have a much lower transmitter power level than the transmitters in the base station. Base stations are connected to a mobile switching center (MSC) typically by a high speed telephone line or microwave radio system. This interconnection must allow both voice and control information to be exchanged between the switching system and the base station. The MSC is connected to the telephone network to allow mobile telephones to be connected to standard landline telephones.

There are many types of analog and digital cellular systems in use throughout the world. Analog systems include AMPS, TACS, JTACS, NMT, MCS and CNET. 

Advanced Mobile Phone Service (AMPS)

Advanced mobile phone service (AMPS) is an analog cellular communications system that uses frequency-division multiple Access (FDMA) for control and frequency division duplex (FDD) for two transmission. The AMPS radio channel types include 30 kHz FSK control channels and 30 kHz voice channels and it operates in the 825 MHz to 890 MHz frequency range.

In 1974, 40 MHz of spectrum was allocated in the United States for cellular service [ ] that provided only 666 channels. In 1986, an additional 10 MHz of spectrum was added to facilitate expansion [ ] of the system to 832 channels. 

The frequency bands for the AMPS system are 824 MHz to 849 MHz (uplink) and 869 MHz to 894 MHz (downlink). Of the 832 channels, AMPS systems are divided into A and B bands to allow for 2 different service providers. There are two types of radio channels in an AMPS system; dedicated control channels and voice channels. On each system (A or B), mobile telephones scan and tune to one of 21 dedicated control channels to listen for pages and compete for access